Hardware |
WAN |
1 x 10/100BASE-TX RJ45 port |
LAN |
1 x 10/100BASE-TX RJ45 port |
Voice |
8 x RJ11 connection (4 x FXS, 4 x FXO) |
Protocols and Standard |
Data Networking |
IPv4 (RFC 791) and IPv6 IPv6 auto configuration (RFC 4862) IPv6 only, IPv4 only or dual stack MAC address (IEEE 802.3) MAC clone setting Vendor Class ID IP / ICMP / ARP / RARP / SNTP Static IP DHCP Client (RFC 2131), WAN port DHCP Server, LAN port NAT Server (RFC 1631) PPPoE Client / DNS Client / TFTP Client DDNS (Planet DDNS, Easy DDNS, DynDNS) Firewall URL / IP / MAC / Port filter Application program filter Port forwarding (TCP, UDP or both) Bandwidth control (download and upload), maximum bandwidth priority setting UPnP server at LAN port Behind NAT, use DMZ for NAT traversal SNTP with time zone and daylight saving TCP/UDP (RFC 793/768), RTP/RTCP (RFC 1889/1890), IPV4 ICMP (RFC 792) VoIP VLAN supports 802.1Q, 802.1P VLAN ID range: 2 to 4094 VLAN priority: 0 to 7 (highest priority) QoS: DiffServ (RFC 2475), TOS (RFC 791/1394) |
Voice Gateway |
RFC 3261 compliance Supports up to 24 SIP trunks to register SIP UDP Protocol Supports SIP compact form Supports SIP Hold Type: Send only, 0.0.0.0 or inactive SIP Session Timer (RFC 4028) SIP Session Refresher: UAC or UAS SIP encryption MD5 digest authentication (RFC 2069/2617) Reliability of provision response PRACK (RFC 3262) Early/Delay media support Offer/Answer (RFC 3264) Message Waiting Indication (RFC 3842) Event notification (RFC 3265) REFER (RFC 3515) Supports outbound proxy Supports primary and backup SIP server Supports STUN NAT Traversal Supports “rport” parameter (RFC 3581) Configure SIP local port SIP QoS type: DiffServ or QoS Accept proxy only: Yes or No |
Audio Codec |
G.711 A-law/μ-law, G.729A, G.723.1 (6.3K, 5.3K) Select voice codec priority: Local or remote Voice payload size (ms) configuration Silence suppression VAD/CNG LEC: Line Echo Canceller Max Echo Tail Length (G.168): 32, 64 and 128ms Packet Loss Compensation Automatic Gain Control In-band / out of band DTMF (RFC 4733, RFC 2833 / SIP INFO) Adaptive/Configurable jitter buffer G.168 Acoustic Echo Cancellation Configure RTP basic port RTP QoS type: DiffServ or TOS Phone book (50 records) for peer to peer calls Dialing plan with drop, replace, insert dialing digits Selects first digit and inter digit timeout duration (Sec) Selectable Call Progress Tone Support Specified Line Calling |
Functions |
Call Functions |
Supports peer to peer dialing 4-line FXO connects to PSTN Line 4-line FXS connects to analog phone set or PABX. Caller ID recognition DTMF (before/after 1st ring) and FSK (before 1st ring), ETSI and Bellcore DTMF Caller ID start and stop bit configurable Current drop detection to release FXO port Disconnect tone recognition to release FXO port Tone Generation: Ring Back, Dial, Busy, Call Waiting, ROH, Warning, Holding, Stutter Dial Tone and Disconnected Tone Configure Tone Frequency, Cadence, Level and Cycle Select Tone specification by country name list Global Country based Tone Specification NAT Traversal supports STUN, UPNP and Behind NAT Out-of-Band DTMF with RFC 2833 and SIP info RFC2833 Payload type: 101 or 96 DTMF send out ON and OFF time configuration DTMF incoming recognition minimum ON and OFF time DTMF Relay Volume configuration T.38 Fax Volume configuration Flash Time transmit via SIP info (enable or disable) Message Waiting Indication (Stutter Tone Notice) Blocks Anonymous Call Call Hold, Call Transfer |
FXO/FXS Line Configuration |
Activates or deactivates: Line ID, line phone number Polarity reversal detection or generation for call establishment and billing Hot line to desired phone number Plays voice file to incoming call Repeats playing voice file counts Self-recorded voice files to upload Generates Flash Time to PSTN network T.38 or Fax Relay Type Incoming and outgoing dB value configurable Dialing Answer Delay time to establish call path Answers PSTN incoming call following the number of rings VoIP dial to FXO/PSTN Line: 1 stage dialing and 2 stage dialing Outgoing SIP Caller ID selection Supports 24 SIP trunk Accepts desired SIP Proxy incoming calls only |
Flexible Routing Plan |
Prefix match and length Priority ring Cyclic ring Simultaneous ring Programmable hunting cycle Backup routes with digit manipulation Default routes |
Flexible Dial Plans |
Retrieves transfer call from 3rd party by dial code (default: *#) Inter digit time out setting First digit dial out delay time setting End of dial keypad number Dial rule: Match dial prefix and maximum digits length (1-15) Phone book can be exported or imported |
FXS Analog 2-wire Interface |
Flash Time Detection: range from 80 to 800 ms ON-HOOK Voltage -48V DC Configures ring cadence, frequency and voltage Supports polarity reversal for billing Service up to 1km in distance to analog telephone set Generate Current Drop Time (Open Loop Disconnect time) |
FXO Analog 2-wire Interface |
Incoming Ring frequency recognition range: 10 to 70 Hz Incoming Ring ON time recognition range: 0 to 8000ms Incoming Ring OFF time recognition range: 0 to 8000ms Incoming Ring Level recognition range: 10 to 95Vrms Flash Time Detection: range from 80 to 800 ms Configures ring cadence, frequency and voltage |
Management |
Administrative Telnet CLI and HTTP, HTTPS HTTP provision through MAC address Multilingual Web user interface 3 levels of user access right with password protection with a different Web language (Administrator, Supervisor and User) HTTP/HTTPS service access limitation from WAN port Configures service ports at HTTP, HTTPS and Telnet services Phone debug module: Device Control, Call Control, DB, Verbose SIP debug module: Register, Call, SIP Message, Others SNTP debug module Device debug module DSP debug Provides system status logs Connect to external Syslog server Status display: Network, line, SIP trunk status Diagnostics (debug through Syslog event notice) Debug in real time by Telnet Auto provision via HTTP server SNMP v2 / Trap Configuration Backup/Restore Dual Firmware Image Backup Reset to factory default |
Environments |
Power Requirements |
12V DC, 3.33A |
Operating Temperature |
0 ~ 45 degrees C |
Operating Humidity |
10%~90% relative humidity, non-condensing |
Weight (with package) |
2.3kg |
Dimensions (W x D x H) |
440 x 110 x 45 mm |
Emission |
CE, FCC, RoHS |
Connectors |
Two 10/100BASE-TX RJ45 Ethernet ports Eight RJ11 ports DC power jack |