Hardware Specification |
VDSL Interface |
VDL-2420MR: 24-Port VDSL2 Line via 1 RJ-21 (Telco-50) connector
VDL-2420MR48: 24-Port POTS/Telephone via 1 RJ-21 (Telco-50) connectors |
1000Mbps Copper Ports |
2 10/100/1000Mbps RJ-45 Auto-Negotiation, Auto MDI/MDI-X |
SFP / mini-GBIC Slots |
2 1000Base-SX/LX/BX, shared with Port-25 ~ Port-26 |
Console |
1 x RS-232 Serial Port (DB9, 57600, N, 8, 1) |
Surge Protect |
3KV |
Switch Architecture |
Store-and-Forward |
Switch Fabric |
8.8Gbps / non-blocking |
Switch Throughput |
6.547Mpps @64Bytes |
Address Table |
8K entries |
Share Data Buffer |
512Kbytes |
Maximum Frame Size |
9K Bytes |
Flow Control |
Back pressure for Half-Duplex IEEE 802.3x Pause Frame for Full-Duplex |
LED |
System: Power, SYS Status Alert: FAN 1, FAN 2, Power 1, Power 2 VDSL: VDSL Link/Sync. Gigabit Port: 1000 Link/Active, 100 Link/Active |
Reset Button |
< 5 sec: System reboot > 10 sec: Factory Default |
Dimension (W x D x H) |
440 x 300 x 88 mm, 2U height |
Weight |
6.4kg |
Power Requirement |
AC Input VDL-2420MR: 100~240V AC, 50-60 Hz VDL-2420MR48: Optional AC Power module
DC Input VDL-2420MR: Optional DC Power module VDL-2420MR48: -48V DC; Range: 30V~60V |
Power Consumption / Dissipation |
130Watts maximum / 404 BTU/hr maximum |
Standard Accessory |
- 2-Meter Telco-50 Cable x 2 - FAN Module x 1 - 19” rack mount kit |
VDSL2 |
VDSL2 Standard |
Comply with ITU-T G.993.2. Supports provisioning the VDSL optional band (25K to 138K Hz) usage ITU-T G.994.1: Handshake procedure of each DMT xDSL circuit ITU-T G.997.2: Physical layer management of each DMT xDSL circuit |
Encoding |
VDSL-DMT |
VDSL2 Template |
Configurable Line Template Configurable Alarm Template |
VDSL2 Profile |
Selectable spectrum profile of - 8a / 8b / 8c / 8d / 12a / 12b / 17a / 30a |
Band Plan |
Selectable band plan for each VDSL line on a per port basis Band plan A: - Profile 998, Annex A of G.993.1; Optimized for symmetric services Band plan B: - Profile 997, Annex B of G.993.1 ; Optimized for asymmetric services |
Rate Adaptation |
Manual RaInit Dynamics |
Power Back-Off |
Downstream Power Back-Off (DPBO) PSD Upstream Power Back-Off (UPBO) PSD |
VDSL2 Features |
Selectable rate limit control Selectable target SNR (signal to Noise Ratio) mode POTS voices pass through |
POTS Splitter |
Compliant with ETSI TS 101 952-1-1 option A for European The splitter is passive element. Even the system is loss of power, the POTS service is still OK |
Layer 2 Function |
Management Interface |
Console, Telnet, Web Browser, SSL, SNMPv1 / v2c / v3 |
Gigabit Port Configuration |
Port disable / enable Auto negotiation 10/100/1000Mbps full and half duplex mode selection Flow Control disable / enable |
Gigabit Port Status |
Display each port’s speed duplex mode, link status and Flow control status Auto negotiation status, trunk status |
Port Mirroring |
TX / RX / Both 1 to 1 monitor |
Bandwidth Control |
Ingress / Egress rate limit control Gigabit Port: • Allow to configure per 128Kbps VDSL2 Port: • Allow to configure per 4Kbps |
VLAN |
IEEE 802.1Q Tag-Based VLAN, up to 256 VLAN groups, out of 4041 VLAN IDs Port-Based VLAN, up to 26 VLAN groups GVRP, up to 128 dynamic VLAN groups Q-in-Q tunneling Private VLAN Edge (PVE / Protected port) with two protected port groups Supports Asymmetric VLAN membership configuration |
Spanning Tree Protocol |
IEEE 802.1D Spanning Tree IEEE 802.1s Multiple Spanning Tree Up to 16 MST instances (0~15) |
Link Aggregation |
Static Port Trunk IEEE 802.3ad LACP (Link Aggregation Control Protocol) 13 groups of 8-Port trunk support |
QoS |
4 priority queue Traffic classification based on - Port priority - 802.1p priority - DSCP / TOS field in IP Packet VoIP QoS by application protocol no. |
IGMP Snooping |
IGMP (v1/v2) Snooping, up to 256 multicast Groups |
Access Control List |
IP-Based Layer 3 / Layer 4 ACL Up to 200 ACL rule entries |
Security |
Port Security – supports per port MAC limit up to 64 entries Static MAC and MAC Filter – up to 256 MAC address entries Source IP / Source MAC Address and Port binding IEEE 802.1X Port-Based Network Access Control – supporting authentication types: - EAP-MD5 / EAP-TLS / EAP-PEAP |
SNMP MIBs |
RFC-1213 MIB-II RFC-2863 Interface MIB RFC-2665 EtherLike MIB RFC-1493 Bridge MIB RFC-2819 RMON MIB (Group 1, 2, 3,9) RFC-2737 Entity MIB RFC 5650 VDSL2 MIB |
Standards Conformance |
Regulation Compliance |
FCC Part 15 Class A, CE |
Standards Compliance |
IEEE 802.3:10Base-T IEEE 802.3u:100Base-TX IEEE 802.3z:1000Base- SX / LX IEEE 802.3ab:1000Base-T IEEE 802.3x:Flow Control and Back pressure IEEE 802.3ad:Link Aggregation Control Protocol (LACP) IEEE 802.1D:Spanning tree protocol IEEE 802.1s:Multiple Spanning tree protocol IEEE 802.1p:Class of service IEEE 802.1Q:VLAN tagging IEEE 802.1x:Port-based authentication network control ITU-T:G.997.1 G.993.2 VDSL2 (Profile 30a Support), Annex A RFC 768:UDP RFC 783:TFTP RFC 791:IP RFC 792:ICMP RFC 854:Telnet RFC 2068:HTTP RFC 1112:IGMP version 1 RFC 1157:SNMPv1 RFC 1902:SNMPv2 RFC 2236:IGMP version 2 RFC 5424:Syslog |
Cables |
• VDSL2: twisted-pair telephone wires (AWG24 or better) up to 1.4km • 10/100Base-TX: 2-Pair UTP Cat.5, up to 100m (328ft) • 1000Base-T: 4-pair UTP Cat.5E, up to 100m • 1000Base-SX: 50/125µm and 62.5/125µm fiber-optic cable, up to 550m • 1000Base-LX: 9/125µm fiber optic cable, up to 10km 50/125µm and 62.5/125µm fiber-optic cable, up to 550m |
Environment |
Temperature |
0~50 Degree C |
Humidity |
5~95% (non-condensing) |